Home  |  Forums  |  914 Info  |  Blogs
 
914World.com - The fastest growing online 914 community!
 
Porsche, and the Porsche crest are registered trademarks of Dr. Ing. h.c. F. Porsche AG. This site is not affiliated with Porsche in any way.
Its only purpose is to provide an online forum for car enthusiasts. All other trademarks are property of their respective owners.
 

Welcome Guest ( Log In | Register )

 
 Reply to this topicStart new topic
> Repairing the main seal leak, Finally got to the first part of it.
mmichalik
post Nov 11 2024, 09:46 AM
Post #1


MikeM
***

Group: Members
Posts: 732
Joined: 27-January 16
From: Valley Center, CA
Member No.: 19,600
Region Association: Southern California
I was able to get some time this weekend, at the cost of all of the household chores, to pull the motor so I can start repairing the main seal leak.
I was a bit nervous about doing it for the first time but, It was relatively straight forward and much easier then I thought it would be.
Hopefully I can get back to the job this weekend so we can button this thing up and I can start driving it again.
Thanks to @ChrisFoley for the engine lift plate. Thing worked like a charm!
Here are a couple pictures:


Attached thumbnail(s)
Attached Image Attached Image
User is offlineProfile CardPM
Go to the top of the page
+Quote Post
mmichalik
post Nov 11 2024, 09:50 AM
Post #2


MikeM
***

Group: Members
Posts: 732
Joined: 27-January 16
From: Valley Center, CA
Member No.: 19,600
Region Association: Southern California
Dropped the engine so I can fix the oil leak


Attached thumbnail(s)
Attached Image
User is offlineProfile CardPM
Go to the top of the page
+Quote Post
JeffBowlsby
post Nov 11 2024, 10:02 AM
Post #3


914 Wiring Harnesses
*****

Group: Members
Posts: 8,750
Joined: 7-January 03
From: San Ramon CA
Member No.: 104
Region Association: None
While you are in ther you have to at least get a valve adjustment, and what else can you do that will save you time later?

;)
User is online!Profile CardPM
Go to the top of the page
+Quote Post
mmichalik
post Nov 11 2024, 10:21 AM
Post #4


MikeM
***

Group: Members
Posts: 732
Joined: 27-January 16
From: Valley Center, CA
Member No.: 19,600
Region Association: Southern California
QUOTE(JeffBowlsby @ Nov 11 2024, 08:02 AM) *

While you are in ther you have to at least get a valve adjustment, and what else can you do that will save you time later?

(IMG:style_emoticons/default/wink.gif)


Great suggestions. I will do just that.
Thanks @JeffBowlsby
User is offlineProfile CardPM
Go to the top of the page
+Quote Post
rjames
post Nov 11 2024, 11:23 AM
Post #5


I'm made of metal
****

Group: Members
Posts: 4,145
Joined: 24-July 05
From: Shoreline, WA
Member No.: 4,467
Region Association: Pacific Northwest
I'd also do the oil cooler seals. Although, based on how clean everything looks, I'm' guessing you don't need them. (IMG:style_emoticons/default/smile.gif)
User is offlineProfile CardPM
Go to the top of the page
+Quote Post
JeffBowlsby
post Nov 11 2024, 02:07 PM
Post #6


914 Wiring Harnesses
*****

Group: Members
Posts: 8,750
Joined: 7-January 03
From: San Ramon CA
Member No.: 104
Region Association: None
Unless you know they are recently changed, if it were me I would also replace the front & rear main seals, the front trans shaft seal and inspect the clutch disk and first/reverse gear assembly
User is online!Profile CardPM
Go to the top of the page
+Quote Post
mmichalik
post Nov 11 2024, 02:56 PM
Post #7


MikeM
***

Group: Members
Posts: 732
Joined: 27-January 16
From: Valley Center, CA
Member No.: 19,600
Region Association: Southern California
The entire unit, from front to back, has probably less than 200 miles on it since the rebuild of the engine and transmission. Which I had done by people who definitely know what they are doing and is why it's so clean right now.
Checking the valves, while it's out is a good idea. The other pieces should be brand new.
The rear main seal was not put in with a tool, just by hand and I think that's the culprit. Particularly since the hand that put it in was unskilled (read = Mine) when we put the clutch on and mated the transmission to the engine.
I will eyeball everything that has been mentioned though, just to make sure.
User is offlineProfile CardPM
Go to the top of the page
+Quote Post
Jack Standz
post Nov 11 2024, 03:25 PM
Post #8


Member
**

Group: Members
Posts: 395
Joined: 15-November 19
From: Happy Place (& surrounding area)
Member No.: 23,644
Region Association: None
When you put the new seal in, this tool helps get things lined-up properly:

https://gowesty.com/products/rear-main-flyw...=41426745753765

And, you should check the clutch disk. If it's contaminated with oil, best to replace it now.
User is offlineProfile CardPM
Go to the top of the page
+Quote Post
mmichalik
post Nov 11 2024, 03:34 PM
Post #9


MikeM
***

Group: Members
Posts: 732
Joined: 27-January 16
From: Valley Center, CA
Member No.: 19,600
Region Association: Southern California
QUOTE(Jack Standz @ Nov 11 2024, 01:25 PM) *

When you put the new seal in, this tool helps get things lined-up properly:

https://gowesty.com/products/rear-main-flyw...=41426745753765

And, you should check the clutch disk. If it's contaminated with oil, best to replace it now.

That's the one I purchased already. Glad to see I grabbed the right thing.
I've ordered a new clutch disk as well. If the amount of oil that spilled out is any indication, it will probably need to be replaced and if not, I'm building a new engine that I can use it on.
User is offlineProfile CardPM
Go to the top of the page
+Quote Post
930cabman
post Nov 14 2024, 05:58 AM
Post #10


Advanced Member
****

Group: Members
Posts: 3,705
Joined: 12-November 20
From: Buffalo
Member No.: 24,877
Region Association: North East States
Might check the trans input shaft also for leakage
User is offlineProfile CardPM
Go to the top of the page
+Quote Post
Superhawk996
post Nov 14 2024, 08:13 AM
Post #11


914 Guru
*****

Group: Members
Posts: 6,533
Joined: 25-August 18
From: Woods of N. Idaho
Member No.: 22,428
Region Association: Galt's Gulch
(IMG:style_emoticons/default/smilie_pokal.gif) on knowing how to drop the engine / trans / exhaust / muffler as an assembly. This is the easiest way to do it in my opinion.
User is online!Profile CardPM
Go to the top of the page
+Quote Post
mmichalik
post Nov 14 2024, 11:33 AM
Post #12


MikeM
***

Group: Members
Posts: 732
Joined: 27-January 16
From: Valley Center, CA
Member No.: 19,600
Region Association: Southern California
QUOTE(Superhawk996 @ Nov 14 2024, 06:13 AM) *

(IMG:style_emoticons/default/smilie_pokal.gif) on knowing how to drop the engine / trans / exhaust / muffler as an assembly. This is the easiest way to do it in my opinion.

Thanks! It just seemed like the most logical way to do it.
Now, I just have to wait for parts to arrive. Hopefully I will be able pull things apart and get ready for the new parts this weekend.
User is offlineProfile CardPM
Go to the top of the page
+Quote Post
technicalninja
post Nov 14 2024, 12:29 PM
Post #13


Advanced Member
****

Group: Members
Posts: 2,013
Joined: 31-January 23
From: Granbury Texas
Member No.: 27,135
Region Association: Southwest Region
Raby does case mods to help the RMS housing drain. He puts a little V in the parting line at the bottom.

The original set up has a drain as well. It's just higher than it needs to be.

Make SURE the original drain path is OPEN or you will be doing this again!

Best "practice" is a large drain on the bottom and a smaller air vent on the top.

The OEM has only the drain about halfway up the recess.
User is offlineProfile CardPM
Go to the top of the page
+Quote Post
bkrantz
post Nov 14 2024, 08:15 PM
Post #14


914 Guru
*****

Group: Members
Posts: 8,154
Joined: 3-August 19
From: SW Colorado
Member No.: 23,343
Region Association: Rocky Mountains
Welcome to the drop the engine club. If you do it 2 or 3 more times, it will become a normal reflex for just about any reason.
User is offlineProfile CardPM
Go to the top of the page
+Quote Post
porschetub
post Nov 14 2024, 09:12 PM
Post #15


Advanced Member
****

Group: Members
Posts: 4,729
Joined: 25-July 15
From: New Zealand
Member No.: 18,995
Region Association: None
QUOTE(mmichalik @ Nov 15 2024, 05:33 AM) *

QUOTE(Superhawk996 @ Nov 14 2024, 06:13 AM) *

(IMG:style_emoticons/default/smilie_pokal.gif) on knowing how to drop the engine / trans / exhaust / muffler as an assembly. This is the easiest way to do it in my opinion.

Thanks! It just seemed like the most logical way to do it.
Now, I just have to wait for parts to arrive. Hopefully I will be able pull things apart and get ready for the new parts this weekend.

Never used seal installer but up to you if not confident on a replacement fitting ,IMO its more important what seal you use , I won't touch anything that isn't a known brand such as Kaco ,Elring etc,I avoid Victor Reinz as found a poor fit in my 911 motor case to the point I have no trust now, they do make great gaskets however.
A good lick of motor oil on the crank and seal lip and a small bit on the OD of the seal helps it go in better you will be fine .
User is offlineProfile CardPM
Go to the top of the page
+Quote Post
mmichalik
post Nov 15 2024, 09:18 AM
Post #16


MikeM
***

Group: Members
Posts: 732
Joined: 27-January 16
From: Valley Center, CA
Member No.: 19,600
Region Association: Southern California
QUOTE(porschetub @ Nov 14 2024, 07:12 PM) *

QUOTE(mmichalik @ Nov 15 2024, 05:33 AM) *

QUOTE(Superhawk996 @ Nov 14 2024, 06:13 AM) *

(IMG:style_emoticons/default/smilie_pokal.gif) on knowing how to drop the engine / trans / exhaust / muffler as an assembly. This is the easiest way to do it in my opinion.

Thanks! It just seemed like the most logical way to do it.
Now, I just have to wait for parts to arrive. Hopefully I will be able pull things apart and get ready for the new parts this weekend.

Never used seal installer but up to you if not confident on a replacement fitting ,IMO its more important what seal you use , I won't touch anything that isn't a known brand such as Kaco ,Elring etc,I avoid Victor Reinz as found a poor fit in my 911 motor case to the point I have no trust now, they do make great gaskets however.
A good lick of motor oil on the crank and seal lip and a small bit on the OD of the seal helps it go in better you will be fine .

I have the Elring seal for this job. The one I had in there was from GoWesty but like I said, I'm sure we damaged it putting it in.
Hopefully, it's "2nd time is a charm" on this (IMG:style_emoticons/default/smile.gif)
User is offlineProfile CardPM
Go to the top of the page
+Quote Post
Superhawk996
post Nov 15 2024, 11:14 AM
Post #17


914 Guru
*****

Group: Members
Posts: 6,533
Joined: 25-August 18
From: Woods of N. Idaho
Member No.: 22,428
Region Association: Galt's Gulch
Pay close attention to the flywheel sealing surface. If you have a groove there - it will never seal properly regardless of what seal you use.
User is online!Profile CardPM
Go to the top of the page
+Quote Post
930cabman
post Nov 15 2024, 01:40 PM
Post #18


Advanced Member
****

Group: Members
Posts: 3,705
Joined: 12-November 20
From: Buffalo
Member No.: 24,877
Region Association: North East States
QUOTE(bkrantz @ Nov 14 2024, 09:15 PM) *

Welcome to the drop the engine club. If you do it 2 or 3 more times, it will become a normal reflex for just about any reason.


"normal", I joined the club figuring you guys were all nuts and hoped I might fit right in
User is offlineProfile CardPM
Go to the top of the page
+Quote Post
« Next Oldest · 914World Garage · Next Newest »
 

Reply to this topicStart new topic
1 User(s) are reading this topic (1 Guests and 0 Anonymous Users)
0 Members:

 

Display Mode: Standard · Switch to: Linear+ · Switch to: Outline

Track this topic · Email this topic · Print this topic · Subscribe to this forum

- Lo-Fi Version Time is now: 28th November 2024 - 12:54 AM
Invision Power Board v9.1.4 © 2024  IPS, Inc.
All rights reserved 914World.com © since 2002
914World.com is the fastest growing online 914 community!
We have it all, classifieds, events, forums, vendors, parts, autocross, racing, technical articles, events calendar, newsletter, restoration, gallery, archives, history and more for your Porsche 914 ...